RAD Data comm FCD-V35 Specifikace Strana 201
- Strana / 228
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Installation and Operation Manual Appendix D Supervision Terminal Commands
FCD-E1LC Ver. 1.0 Commands D-35
Parameter Function Values Configuration Guidelines
LOG_OFF
Controls the idle
disconnect time of
the CONTROL DCE
port
NO – Automatic session
disconnection disabled. To end
the session, use the BYE
command.
3_MIN – Automatic
disconnection after 3 minutes if
no data is received by the
CONTROL DCE port.
10_MIN – Automatic
disconnection after 10 minutes
if no data is received by the
CONTROL DCE port.
Default: NO
CALL_OUT_
TRIGGER
Selects the type of
alarms that will
trigger the call-out
function (reporting
of alarms via a
modem connected
to the CONTROL
DCE port)
NONE – The call-out function is
disabled.
ALL – FCD-E1LC will initiate a call
after each new alarm.
MAJOR – FCD-E1LC will initiate a
call only when a new major
alarm condition is detected.
Default: NONE
ACTIVATE_
CALL_OUT
If CALL_OUT_
TRIGGER is not set
to NONE, defines
when the call-out
function is activated
ANY CASE – Call-out is activated
in any case.
LINK FAIL – Call-out is activated
only when a link failure occurs or
there is local or remote
synchronization loss.
Default: ANY CASE
AUXILIARY_
DEVICE
Selects the
management mode
supported by the
CONTROL DCE port.
TERMINAL – The CONTROL DCE
port is connected using an ASCII
supervision terminal.
NMS-SLIP – The CONTROL DCE
port connects to an SNMP
management station and/or
Telnet host using the SLIP
protocol.
NMS-PPP – The CONTROL DCE
port connects to an SNMP
management station and/or
Telnet host using the PPP
protocol.
SLIP-AGENT – The CONTROL DCE
port connects to another agent
port using the SLIP protocol. See
additional details in
Appendix B
.
Default: TERMINAL
Select NMS-SLIP or NMS-PPP
when the supervisory port
must be able to use the SLIP,
respectively NMS protocol, for
example for SNMP or Telnet
management.
If the management connection
to the FCD-E1LC CONTROL DCE
port uses a chain topology (for
example, when it is connected
to the serial port of a
Megaplex-2100), select
SLIP-AGENT.
Select TERMINAL if only the
supervision terminal must be
supported.
- FCD-E1LC 1
- Limited Warranty 4
- Product Disposal 4
- General Safety Instructions 5
- Safety Symbols 5
- Handling Energized Products 6
- Caution 8
- Attention 8
- FCC-15 User Information 9
- Mise au rebut du produit 10
- Symboles de sécurité 10
- Français 11
- Declaration of Conformity 13
- Quick Start Guide 15
- 3. Cable Connections 16
- Configuration Procedure 17
- Contents 19
- Chapter 1 21
- Introduction 21
- Main Features 22
- 1.2 Typical Applications 23
- 1.3 Physical Description 24
- 1.4 Functional Description 25
- Internal Bus Functions 27
- Main Link Interface 28
- Sublink Interface 29
- Synchronous Data Channels 30
- Ethernet Interface 31
- Ethernet Switch Description 32
- Flow Control Options 32
- Forwarding Algorithms 33
- VLAN and QoS Support 33
- System Timing 34
- Main Link Timing 34
- Sublink Timing 34
- Diagnostics 35
- Timeslot Handling 36
- Management Subsystem 36
- Power Supply Subsystem 38
- 1.5 Timing Considerations 39
- System Management Method 40
- Management Access Options 41
- Serial Ports 42
- MBE/RAS/A 42
- Diagnostics 48
- Indicators 48
- Chapter 2 51
- Installation and Setup 51
- Physical Requirements 53
- Power Requirements 53
- Connections 53
- Serial Data Port Connections 54
- Ethernet Port Connections 54
- 2.3 Package Contents 55
- 2.4 Equipment Needed 56
- 2.5 FCD-E1LC Enclosures 56
- FCD-E1LC Rear Panels 57
- Opening the Unit 60
- Figure 2-4 61
- Figure 2-5 61
- 1. Refer to 62
- Table 2-4 63
- Closing the Unit 64
- 2.7 Connecting the Cables 65
- Connecting the Sublink 66
- Connecting the Data Channels 66
- Connecting Ethernet 66
- 2.8 Connecting to Power 67
- Chapter 3 69
- Operation 69
- 3.2 Indicators 70
- Preliminary Configuration 71
- System Configuration 71
- Routine Management 72
- Autobaud Function 74
- 3.4 Turning Off the Unit 75
- Configuration 77
- Starting a Control Session 78
- Configure the SNMP Agent 80
- Ending the Control Session 81
- Command Syntax 81
- What to Do If … 82
- Ending a Control Session 83
- Command Options 84
- Index of Commands 84
- Chapter 5 87
- Configuring FCD-E1LC for 87
- Chapter 3 88
- 5.2 Configuration Example 88
- Configure System Timing 92
- Chapter 6 93
- Troubleshooting and 93
- 6.2 Detecting Errors 96
- 6.3 Handling Alarms 96
- Alarm Display 97
- Alarm Messages 97
- FCD-E1LC Ver. 1.0 100
- 6.4 Troubleshooting 103
- Appendix B 104
- Allowed Loopback 105
- Combinations 105
- Troubleshooting Procedure 106
- 6.5 Testing the Unit 108
- Local FCD-E1LC 109
- Remote FCD-E1LC 110
- BER Testing (LP BERT ML) 112
- Sublink Loopbacks 113
- Data Channel Loopbacks 115
- 6.7 Technical Support 121
- Appendix A 123
- Connection Data 123
- Figure A-2 124
- A.2 Sublink Connection Data 125
- Pin 13 Pin 1 126
- DCE Mode 127
- DTE1 Mode 128
- DTE2 Mode 129
- X.21 Data Channel 133
- Figure A-9 138
- Connector Data 140
- Connector 141
- Table A-15 141
- A.7 Power Connection 142
- SNMP Management 143
- SNMP Operations 144
- MIB Structure 144
- SNMP Communities 145
- B.2 SNMP Traps 146
- Appendix C 149
- Operating Environment 149
- G732N Multiframe 150
- G732S Multiframe 150
- E1 Line Signal 151
- Timeslot 0 151
- E1 Line Alarm Conditions 152
- C.2 IP Environment 153
- (13 bits) 154
- IP Address Structure 155
- Host Portion 156
- Subnetting 157
- Subnet Masks 157
- IP Routing Principles 158
- Ethernet LAN Topologies 159
- Media Access Method 160
- Autonegotiation 161
- Figure A-4 162
- Bridging 163
- ARP Protocol 165
- Appendix D 167
- Supervision Terminal 167
- Commands 167
- D.2 Commands 168
- Purpose 169
- <Enter> to continue 170
- DEF ALM MASK 171
- Chapter 4 172
- DEF BERT ML 174
- DEF CALL 176
- Table D-3 177
- Use – Serial Data Channel 179
- Use – Ethernet Port 185
- DEF DNLOAD 186
- DEF MANAGER LIST 189
- DEF NAME 192
- DEF NODE 192
- DEF PROMPT 192
- DEF PWD 193
- DEF ROUTE 194
- Table D-8 195
- DEF SYS 202
- DEF TERM 203
- DSP AGENT 204
- DSP ALM 204
- DSP BERT ML 205
- DSP HDR TST 206
- DSP MANAGER LIST 207
- DSP PM ML 207
- DSP PM SL 210
- DSP REM AGENT 210
- DSP ST CH 211
- DSP ST ML 212
- DSP ST SL 214
- DSP ST SYS 214
- INIT DB 217
- Syntax & Use 220
- Customer Response Form 223
- Error Report 225
- International Headquarters 228
- North America Headquarters 228
Související produkty a manuály pro Sítě RAD Data comm FCD-V35
Sítě RAD Data comm FCD-IP Uživatelský manuál
(110 stránky)
(110 stránky)
Sítě RAD Data comm ASMi-52 Technické informace
(100 stránky)
(100 stránky)
Sítě RAD Data comm FOM-T3 Specifikace
(42 stránky)
(42 stránky)
Sítě RAD Data comm Optimux-106 Specifikace
(110 stránky)
(110 stránky)
Sítě RAD Data comm ASM-20 Specifikace
(116 stránky)
(116 stránky)
Sítě RAD Data comm T1 Specifikace
(34 stránky)
(34 stránky)
Sítě RAD Data comm Optimux-34 Technické informace
(82 stránky)
(82 stránky)
Sítě RAD Data comm FOM-E3 Uživatelský manuál
(2 stránky)
(2 stránky)
AEG Electrolux SC81843-5I Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Kombikühlschränke AEG Electrolux SC81843-5I.
Wir stellen 1 PDF-Handbücher AEG Electrolux SC81843-5I zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Aeg electrolux SC81843-5I Bedienungsanleitung (24 Seiten)
Marke: Aeg-electrolux | Kategorie: Combi-fridges | Größe: 0.21 MB |
Inhaltsverzeichnis
Weitere Produkte und Handbücher für Kombikühlschränke AEG Electrolux
| Modelle | Dokumententyp |
|---|---|
| S60240KG28 |
Bedienungsanleitung
Aeg-Electrolux S60240KG28 User Manual [de] [fr] [nl] ,
40 Seiten
|
| S75267KG1 |
Bedienungsanleitung
  
Aeg-Electrolux S75267KG1 Handleiding,
88 Seiten
|
| S70342KG |
Bedienungsanleitung
Aeg-Electrolux S70342KG User Manual,
14 Seiten
|
| S70330DT |
Bedienungsanleitung
Aeg-Electrolux S70330DT User Manual,
18 Seiten
|
| S73000DSW0 |
Bedienungsanleitung
Aeg-Electrolux S73000DSW0 Handleiding,
76 Seiten
|
| SC61640-6I |
Bedienungsanleitung
Aeg-Electrolux SC61640-6I User Manual [no] ,
44 Seiten
|
| S70298DT |
Bedienungsanleitung
Aeg-Electrolux S70298DT User Manual [da] [en] [es] [et] [it] [sv] ,
12 Seiten
|
| SCS51600S0 |
Bedienungsanleitung
Aeg-Electrolux SCS51600S0 Handleiding,
68 Seiten
|
| AIK2401R |
Bedienungsanleitung
Aeg-Electrolux AIK2401R User Manual,
92 Seiten
|
| SD91240-4I |
Bedienungsanleitung
Aeg-Electrolux SD91240-4I User Manual [de] [et] [it] [lv] ,
24 Seiten
|
| SC91843-6I |
Bedienungsanleitung
Aeg-Electrolux SC91843-6I User Manual [da] ,
20 Seiten
|
| SC81847-4I |
Bedienungsanleitung
Aeg-Electrolux SC81847-4I User Manual,
48 Seiten
|
| A51900GSW0 |
Bedienungsanleitung
Aeg-Electrolux A51900GSW0 Handleiding,
52 Seiten
|
| SCT71900S0 |
Bedienungsanleitung
Aeg-Electrolux SCT71900S0 User Manual,
28 Seiten
|
| SK91840-5I |
Bedienungsanleitung
Aeg-Electrolux SK91840-5I User Manual,
24 Seiten
|
| S70318KG5 |
Bedienungsanleitung
Aeg-Electrolux S70318KG5 User Manual [en] [nl] [pt] ,
32 Seiten
|
| SN81840-4I |
Bedienungsanleitung
Aeg-Electrolux SN81840-4I User Manual,
14 Seiten
|
| A51900GSW0 |
Bedienungsanleitung
Aeg-Electrolux A51900GSW0 User Manual,
36 Seiten
|
| SCD71800S0 |
Bedienungsanleitung
Aeg-Electrolux SCD71800S0 User Manual,
76 Seiten
|
| SC81640-4I |
Bedienungsanleitung
Aeg-Electrolux SC81640-4I User Manual,
24 Seiten
|
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.026 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce