Data Sheet
Rear Panel
Sig Link A/B (on the fiber optic module)
On (green): signal exists on Link A/B
Off: no signal on Link A/B
LINK/ACT
On (yellow): link is up
Off: link is down
Blinking: frames are transmitted
100
On (green): 100 Mbps mode
Off: 10 Mbps mode
CARD INDICATORS
Link
OP A/B LOS
On (red): Sync/Signal Loss on OP A/B
Off: Normal operation
OP A/B AIS
On (yellow): AIS detected (only for
operating opposite Optimux-108/106
without Ethernet port)
Off: Normal operation
(OP A/B LOS and AIS are On if the SFP is
not inserted.)
Ethernet
OP A/B LINK/ACT
On (yellow): link is up
Off: link is down
Blinking: frames are transmitted
OP A/B 100
On (green): 100 Mbps mode
Off: 10 Mbps mode
GENERAL
Compliance
G.703, G.823 (E1), G.824 (T1), G.955,
IEEE 802.3
G.742 (Optimux-108 without Ethernet ports)
Diagnostics
Local and remote loopbacks on uplink and
on each E1/T1 tributary link
Local loopback on optional V.35 user port
(Optimux-108 only)
Timing
Uplink: internal
E1/T1 tributary: transferred transparently,
independent for each channel
V.35: internal, external, loopback
(Optimux-108 only)
Power
Standalone:
Wide range power supply
• AC: 100 to 240 VAC
• DC: -48 VDC (-40 to -125 VDC)
24 VDC power supply
• 24 VDC (20 to 36 VDC)
Card: supplied by LRS-102
Power Consumption
Standalone:
• Wide-range AC: 25 VA max
• Wide-range DC (-48 VDC): 9W max
• 24 VDC: 9W max
Card: 9W max
Table 2. SFP Fiber Optic Interface Characteristics for OP-108C/106C Cards
Module
Name
Wave-
length
Fiber Type
Transmitter
Type
Typical
Output
Power
Receiver
Sensitivity w/o
USER ETH port
Receiver
Sensitivity with
USER ETH port
Typical Max
Range w/o
USER ETH port
Typical Max
Range with
USER ETH port
Connector
Type
[nm] [dBm] [dBm] [dBm] [km]
[miles] [km] [miles]
SFP-1 1310 62.5/125 multimode LED -18 -31
-30
6.5
4.0
2 1.2
LC
SFP-2 1310 9/125 single mode Laser -12 -31
-28
38
23.6
20 12.4
LC
SFP-2H 1310 9/125 single mode Laser -12 -31
-28
38
23.6
20 12.4
LC
-2 -34
-34
70
43.4
40 24.8
LC
SFP-3 1310 9/125 single mode Long haul laser
-2 -34
-34
70
43.4
40 24.8
LC
SFP-3H 1310 9/125 single mode Long haul laser
-2 -34
-34
120 74.5
80 49.7
LC
SFP-4 1550 9/125 single mode Long haul laser
SFP-10a Tx –1310,
Rx –1550
9/125 single mode
(single fiber)
Laser WDM -12 -30
-28
40
24.8 20 12.4 LC
SFP-10b Tx –1550,
Rx –1310
9/125 single mode
(single fiber)
Laser WDM -12 -30
-28
40
24.8 20 12.4 LC
SFP-18A Tx – 1310,
Rx – 1550
9/125 single mode
(single fiber)
Laser WDM
-2 -30
-28
60 37.3
40 24.8
LC
SFP-18B Tx – 1550,
Rx – 1310
9/125 single mode
(single fiber)
Laser WDM
-2 -30
-28
60 37.3
40 24.8
LC
SFP-24 850 62.5/125 multimode
50/125 multimode
VCSEL -7 -31
-25
6.5
4.0
1
2
0.6
1.2
LC
Note: Typical ranges are calculated according to attenuation of 0.4 dB/km for 1310 nm single mode fiber and 0.25 dB/km for 1550 nm single mode fiber.
Order from: Cutter Networks
Ph: 727-398-5252 / Fx: 727-397-9610
(8 stránky)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce