Rad-data-comm E1 Interface Converter RIC-E1 Uživatelský manuál Strana 86
- Strana / 99
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Appendix D IR-IP Interface Module RIC-E1 Installation and Operation Manual
D-30 Diagnostic Tools (Ping Terminal)
Using the Ping Function
The Ping option is used to confirm IP connectivity by pinging other IP hosts.
Connectivity is confirmed by receiving a reply from the remote (pinged) IP host.
To ping a host:
1. From the Diagnostic Tools menu, type 1 and enter the desired host IP address.
2. Press <Enter> to confirm the destination IP address.
3. To start pinging, type 2 on the Diagnostic Tools screen.
After pinging starts, you can monitor the ping status. A typical screen is
shown in Figure D-29.
After pinging is started, it continues in the background even if you exit the
Diagnostics Tools screen. In this case, a Ping Running message appears in the top
upper left-hand corner of the screen.
4. To stop pinging, type 3 from the Diagnostic Tools menu.
A Ping Stopped message is displayed.
To clear the message and return to the Diagnostic Tools screen, press any
key.
IR_IP <IR-IP> S/W Ver. 1.21 31/IR (date)
Quick Setup
Management Access
Advanced Setup
Device Control
View
Diagnostic Tools (PING terminal)
=====================================================================
1. Ping IP Address :192.168.100.011
2. Start Pinging :>>>
3. Stop Pinging :>>>
Pinging 192.168.212.001 Sent 27 Recvd 25 Lost 2 Resp.Time 60 ms
Press one of the numbers to select or ESC:
Figure D-29. Diagnostic Tools Menu after Receiving Pinging Response
Note
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
www.bestdatasource.com
- E1 Interface Converter 1
- Limited Warranty 4
- General Safety Instructions 5
- Handling Energized Products 6
- FCC-15 User Information 8
- Declaration of Conformity 10
- Quick Start Guide 11
- 2. Operating RIC-E1 12
- Contents 13
- List of Figures 14
- List of Tables 14
- Chapter 1 15
- Introduction 15
- 1.2 Physical Description 16
- 1.3 Functional Description 17
- 1.4 Technical Specifications 18
- Order from: Cutter Networks 19
- Chapter 2 21
- Installation and Setup 21
- 2.3 Configuring RIC-E1 22
- Configuring RIC-E1 2-3 23
- Connecting the Interfaces 24
- Connecting the DTE 25
- Connecting the AC Power 25
- Connecting the DC Power 25
- 2-6 Configuring RIC-E1 26
- Chapter 3 27
- Operation 27
- 3.2 Operating Instructions 28
- Chapter 4 29
- Troubleshooting and 29
- Diagnostics 29
- 4.2 Troubleshooting 30
- 4.3 Technical Support 31
- 4-4 Technical Support 32
- Chapter 5 33
- RIC-E1/R Card 33
- 5-2 ASM-MN-214 Card Cage 34
- 5.2 Power Supply 35
- 5.3 RIC-E1/R Front Panel 36
- Warning 40
- Appendix A 41
- Interface Connector Wiring 41
- [Indication] 41
- [Function] 42
- [Signal 42
- Timing] 42
- A.3 Line Interface Connector 43
- Appendix B 45
- IR-ETH Interface Module 45
- 10B ASE-T 46
- IR-ETH Options B-3 47
- B.3 Technical Specifications 48
- Setting the DIP Switch 49
- LED Indicators 49
- Connecting the LAN 50
- C.1 Introduction 51
- 10/100BASE-T 52
- C.3 Technical Specifications 54
- Setting the DIP Switches 55
- Appendix D 57
- IR-IP Interface Module 57
- D.1 Introduction 58
- 10BaseT LAN 59
- D.3 Physical Description 60
- IR-IP LEDs 61
- IR-IP Controls 61
- Rescue Configuration 64
- IP Learning Mechanism 65
- What to Do If 67
- D.6 IR-IP Management Utility 68
- D.7 Quick Setup Menu 69
- LAN IP Address 70
- LAN IP Mask 70
- WAN IP Address 70
- WAN IP Mask 70
- Default Gateway 70
- RIC-E1 with IR-IP 71
- DHCP Server 71
- LAN IP Address: 192.168.1.2 71
- Mask: 255.255.255.248 71
- IP Network 71
- D.8 Management Access Menu 72
- D.9 Advanced Setup Menu 73
- Device Name 74
- Contact Person 74
- System Location 74
- Advanced Setup Menu D-19 75
- Protocol Field Compression 76
- Authentication Protocol 76
- Security Host/Guest 77
- User Name To Send 77
- Password To Send 77
- User Name To Accept 77
- Password To Accept 77
- Multicast Forwarding 78
- Static Groups 79
- Total Timeout 80
- Start Operation 80
- Server IP Address 80
- File Name 80
- Resetting the Device 81
- Resetting the LAN Interface 81
- Resetting the WAN Interface 82
- ARP Tables 83
- Displaying Statistics 84
- Using the Ping Function 86
- D.14 Erasing IR-IP Software 87
- Erasing Application Software 88
- Downloading New Software 88
- E.1 Introduction 90
- EXT INT/LBT 91
- INT/LBT Clock Mode 92
- Customer Response Form 96
- Error Report 97
Související produkty a manuály pro Hardware Rad-data-comm E1 Interface Converter RIC-E1
Hardware Rad-data-comm ASM-10/8 Uživatelský manuál
(50 stránky)
(50 stránky)
Hardware Rad-data-comm MBE10-1D Uživatelský manuál
(58 stránky)
(58 stránky)
Hardware Rad-data-comm ASMI-450 Uživatelský manuál
(117 stránky)
(117 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.031 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce