RAD Data comm ASMi-52 Uživatelský manuál Strana 11
- Strana / 186
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
ASMi-52 Ver. 2.5 Configuring ASMi-52 1
Quick Start Guide
Installation of ASMi-52 should be carried out only by an experienced technician. If
you are familiar with ASMi-52, use this guide to prepare the units for operation.
1. Installing ASMi-52
Connecting the Interfaces
1. Connect the line to the RJ-45 rear panel connector dedicated SHDSL.
2. Connect the DTE to the appropriate rear panel connector.
3. Connect the control terminal to the rear panel CONTROL connector.
Connecting the Power
• Connect the AC or DC power to the ASMi-52 modem.
The unit has no power switch. Operation starts when power is connected
to the rear panel power connector.
2. Configuring ASMi-52
Configure ASMi-52 to the required operation mode via an ASCII terminal
connected to the rear panel CONTROL port directly or via a modem link.
Connecting the Terminal
To connect the terminal:
1. Connect the terminal cable to the CONTROL connector of ASMi-52.
2. Turn the control terminal on.
3. Configure the terminal to the default communication parameters: 9.6 kbps,
one start bit, eight data bits, no parity, one stop bit.
4. Select the full-duplex mode.
5. Turn the terminal echo off.
6. Disable any type of flow control.
You are now ready to start a control session.
- /4-Wire SHDSL Modem 1
- ASMi-52 3
- Limited Warranty 4
- General Safety Instructions 5
- Handling Energized Products 6
- FCC-15 User Information 8
- Warning 9
- Declaration of Conformity 10
- Quick Start Guide 11
- Configuring the E1 Interface 12
- Configuring the T1 Interface 13
- Contents 15
- Table of Contents 16
- DTE Interface 17
- Line Interface 17
- Unit Enclosure 18
- Functionality 20
- Multiplexer Applications 23
- Management 25
- Statistics Collection 26
- Alarm Reporting 26
- SHDSL Repeaters 26
- 1.4 Technical Specifications 28
- Environment 31
- Chapter 2 33
- Installation and Setup 33
- 2.3 Package Contents 34
- Connecting the Line 35
- Connecting the DTE Interface 35
- Chapter 3 37
- Operation 37
- Preparing the Terminal 43
- Data Terminal Ready (DTR) 43
- Initiating a Control Session 43
- Correcting Entries 44
- Navigating Data Forms 44
- Configuration Menus 47
- Chapter 4 51
- Configuration 51
- Entering Device Information 52
- Configuring the LAN Port 57
- Configuring Aging Timeout 59
- Configuring QoS Mapping 59
- Setting the LAN Rate 60
- Configuring Autonegotiation 61
- Configuring Fault Indication 62
- Configuring Remote Card Mode 65
- Selecting the CTS State 67
- Selecting the DSR State 67
- Timeout 68
- Configuring the Snext Margin 73
- Configuring Line Probing 75
- Selecting E1 Framing Mode 79
- Setting the Sync Mode 80
- Defining Idle Code 81
- Mapping E1 Timeslots 81
- Displaying the System Status 86
- Displaying the Port Status 87
- Accessing the Remote ASMi-52 88
- Updating Software Releases 91
- Resetting ASMi-52 95
- Resetting the ASMi-52 Modem 96
- Resetting the SHDSL Repeater 97
- Chapter 5 99
- Configuring a Typical 99
- Application 99
- ASMi-52 Ver. 2.5 100
- Setting the E1 Port 101
- Chapter 6 105
- Troubleshooting and 105
- Diagnostics 105
- Displaying All Alarms 113
- Masking Port Alarms 115
- 6.4 Troubleshooting 119
- BERT Patterns 121
- Running Loopback Tests 123
- Running the Local Loopback 124
- Running the Remote Loopback 126
- Deactivating the Loopbacks 127
- 6.7 Technical Support 129
- Appendix A 131
- Interface Connector 131
- Specifications 131
- Ethernet Connector 133
- A.2 CONTROL Connector 134
- A.3 Alarm Relay Connector 135
- Appendix B 137
- IR-IP Interface Module 137
- B.2 Technical Specifications 138
- B.3 Physical Description 139
- IR-IP LEDs 140
- Normal Indications 140
- IP Learning Mechanism 143
- General Operating Procedures 145
- ASMi-52 with IR-IP 147
- LAN IP Address: 192.168.1.2 149
- Mask: 255.255.255.248 149
- DHCP Server 149
- IP Network 149
- Defining a Telnet Password 150
- B.9 Advanced Setup 151
- Frame Relay Protocol 153
- PPP Protocol Menu 154
- Downloading New Software 157
- Viewing the Error Log 157
- Reset LAN 158
- Reset WAN 159
- Viewing the ARP Tables 160
- Using the Ping Function 163
- B.14 Erasing IR-IP Software 164
- Erasing Application Software 165
- B.15 IR-IP Troubleshooting 166
- Appendix C 167
- Easy Config Device 167
- C.3 Installation 168
- C.4 Operation 169
- Assigning Timeslots 172
- ASMi-52 Ver. 2.5 I-5 177
- E1, 4-32 177
- Supplement 179
- Customer Response Form 181
- Error Report 183
Související produkty a manuály pro Brány / ovladače RAD Data comm ASMi-52
Brány / ovladače RAD Data comm IPmux-8 Specifikace
(174 stránky)
(174 stránky)
Brány / ovladače RAD Data comm Vmux-210 Specifikace
(192 stránky)
(192 stránky)
Brány / ovladače RAD Data comm IPmux-1E Specifikace
(143 stránky)
(143 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.024 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce