Rad-data-comm MBE10-1D Uživatelský manuál

MBE Family (LAN RANger Series) Installation and Operation ManualEthernet Remote Access Routers (MBE10-1, MBE10-8, MBE10-1D, MBE10-8D) Order from: Cut

Declaration of Conformity Manufacturer's Name: RAD Data Communications Ltd. Manufacturer's Address: 24 Raoul Wallenberg St. Tel Aviv

Conventions A note draws attention to a general rule for a procedure, or to exceptions to a rule. A caution warns of possible damage to the equi

Order from: Cutter NetworksPh:727-398-5252/Fax:727-397-9610www.bestdatasource.com

MBE Family Installation and Operation Manual i Contents Chapter 1. Introduction 1.1 Overview...

Table of Contents ii MBE Family Installation and Operation Manual List of Figures 1-1. MBE Product 3-D View ...

Overview 1-1 Chapter 1 Introduction This chapter: • Provides a general overview of versions of MBE units, features, and ordering options • Provid

Chapter 1 Introduction MBE Family Installation and Operation Manual 1-2 Overview • MBE10-8D is a dual WAN-port router/bridge, As a bridge, it allo

MBE Family Installation and Operation Manual Chapter 1 Introduction Overview 1-3 The Single IP address translation feature permits a small or medi

Chapter 1 Introduction MBE Family Installation and Operation Manual 1-4 Physical Description configuration. If traffic exceeds the defined threshol

MBE Family Installation and Operation Manual Chapter 1 Introduction Functional Description 1-5 link. In addition, it has a LAN interface for conn

Order from: Cutter NetworksPh:727-398-5252/Fax:727-397-9610www.bestdatasource.com

Chapter 1 Introduction MBE Family Installation and Operation Manual 1-6 Functional Description Bridge Mode Compatibility Most members of the MBE ra

MBE Family Installation and Operation Manual Chapter 1 Introduction Functional Description 1-7 MBE10-8 Operation On power-up, both the local and

Chapter 1 Introduction MBE Family Installation and Operation Manual 1-8 Functional Description MainProcessorandCommunication Processor2MBDRAMLANPro

MBE Family Installation and Operation Manual Chapter 1 Introduction Functional Description 1-9 Bridge Mode Filtering Block (MBE10-8 and MBE10-8D

Chapter 1 Introduction MBE Family Installation and Operation Manual 1-10 Technical Specifications Product configurations and software are saved in

MBE Family Installation and Operation Manual Chapter 1 Introduction Technical Specifications 1-11 Control Interface Type V.24/RS-232 Connector R

Chapter 1 Introduction MBE Family Installation and Operation Manual 1-12 Technical Specifications Physical Height 4.4 cm/ 1.8 in (1U) Length 30

Site Requirements and Prerequisites 2-1 Chapter 2 Installation This chapter describes the basic installation procedures for the MBE unit, including

Chapter 2 Installation MBE Family Installation and Operation Manual 2-2 Installation and Setup 2.3 Package Contents The following items are includ

MBE Family Installation and Operation Manual Chapter 2 Installation Installation and Setup 2-3 Configuring MBE This section describes how to conf

MBE Family (LAN RANger Series) Ethernet Remote Access Routers (MBE10-1, MBE10-8, MBE10-1D, MBE10-8D) Version 7 Installation and Operation Manual N

Chapter 2 Installation MBE Family Installation and Operation Manual 2-4 Installation and Setup 9. To enable direct connection between MBE and a U

MBE Family Installation and Operation Manual Chapter 2 Installation Installation and Setup 2-5 Table 2-1. MBE Switches and Jumpers Switch/Jumper

Chapter 2 Installation MBE Family Installation and Operation Manual 2-6 Installation and Setup 03457612BOTRate7682561289664483216POS01234567 00334

MBE Family Installation and Operation Manual Chapter 2 Installation Installation and Setup 2-7 Link-2 TOPDTEDTE/DCEJumperDCELink-1 BOTTOM DTE/DCE

Chapter 2 Installation MBE Family Installation and Operation Manual 2-8 Installation and Setup POWEROIAUITO V.35 LINE100-230 VAC Figure 2-5. MBE

MBE Family Installation and Operation Manual Chapter 2 Installation Installation and Setup 2-9 Connecting the Power AC Power Supply AC power to t

Chapter 2 Installation MBE Family Installation and Operation Manual 2-10 Installation and Setup Order from: Cutter NetworksPh:727-398-5252/Fax:72

Front Panel Controls and Indicators 3-1 Chapter 3 Operation This chapter: • Describes MBE front panel controls and indicators • Provides basic o

Chapter 3 Operation MBE Family Installation and Operation Manual 3-2 Operating Instructions Table 3-1. Front Panel Controls and Indicators (Cont.)

MBE Family Installation and Operation Manual Chapter 3 Operation Operating Instructions 3-3 Power-on  To power-up MBE: 1. Set the POWER switch

Limited Warranty RAD warrants to DISTRIBUTOR that the hardware in the MBE Family (LAN RANger Series) to be delivered hereunder shall be free of def

Chapter 3 Operation MBE Family Installation and Operation Manual 3-4 Operating Instructions Order from: Cutter NetworksPh:727-398-5252/Fax:727-39

Alarms and Troubleshooting 4-1 Chapter 4 Troubleshooting and Diagnostics This chapter provides: • A procedure for performing a ping connectivity

Chapter 4 Troubleshooting and Diagnostics MBE Family Installation and Operation Manual 4-2 Alarms and Troubleshooting If a persistent fault condit

MBE Family Installation and Operation Manual Chapter 4 Troubleshooting and Diagnostics Alarms and Troubleshooting 4-3  To filter the Debug Messa

Chapter 4 Troubleshooting and Diagnostics MBE Family Installation and Operation Manual 4-4 Alarms and Troubleshooting Order from: Cutter Network

A-1 Appendix A Pin Assignment This appendix: • Provides information about the various interfaces and cable connections supported by MBE. Table A-

Appendix A Pin Assignment MBE Family Installation and Operation Manual A-2 Table A-1. Interface Signal List (Female Connectors) (Cont.) Signal

MBE Family Installation and Operation Manual Appendix A Pin Assignment A-3 Shield 1Signal GND 7RTS-a

Appendix A Pin Assignment MBE Family Installation and Operation Manual A-4 1214316179241115124567820APSRTVXUWYAA (a)CDEBFHShieldV.35/ DB-

MBE Family Installation and Operation Manual Appendix A Pin Assignment A-5 1214316419513622202378101512179182124112514226247259271129123019

General Safety Instructions The following instructions serve as a general guide for the safe installation and operation of telecommunications produc

Appendix A Pin Assignment MBE Family Installation and Operation Manual A-6 RJ-45 socketRx pair: pins 3 and 6Tx pair: pins 1 and 21 2 3 4

I-1 Index —B— bridge mode, 1-5 bridges, 1-2 —C— clock, 2-5 COD, 1-3 configuration, 2-3 initial setup, 3-2 control interface, 1-11 control port, 1

Index MBE Family Installation and Operation Manual I-2 switches, 2-5 —T— technical specifications, 1-10 TELNET, 1-2 troubleshooting, 4-2 —X— XMODEM,

24 Raoul Wallenberg St., Tel Aviv 69719, IsraelTel: +972-3-6458181, Fax: +972-3-6483331, +972-3-6498250E-mail: , Web site:

Order from: Cutter NetworksPh:727-398-5252/Fax:727-397-9610www.bestdatasource.com

Error Report Type of Error(s) ❒ Incompatibility with product or Problem(s): ❒ Difficulty in understanding text ❒ Regulatory information (Sa

Order from: Cutter NetworksPh:727-398-5252/Fax:727-397-9610www.bestdatasource.com

Order from: Cutter NetworksPh:727-398-5252/Fax:727-397-9610www.bestdatasource.com

900 Corporate Drive, Mahwah, N.J. 07430, Tel: (201) 529-1100 24 Raoul Wallenberg Street, Tel Aviv 69719, Israel, Tel: 972-3-6458181 U.S. HEADQUARTERS

Handling Energized Products General Safety Practices Do not touch or tamper with the power supply when the power cord is connected. Line voltages

Connection of Data and Telecommunications Cables Data and telecommunication interfaces are classified according to their safety status. The followin

To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cords. Pour réduire les risques s’incendie, utiliser seulement

Canadian Emission Requirements This Class A digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Regulation.